No universal tankless wire gauge exists: an 8 kW unit can draw about 33 amps on one 40-amp circuit with 8 AWG wire, while a 36 kW unit can draw about 150 amps across four 40-amp circuits. The correct tankless water heater wire size depends on the exact model, not just whether the heater is […]
No universal tankless wire gauge exists: an 8 kW unit can draw about 33 amps on one 40-amp circuit with 8 AWG wire, while a 36 kW unit can draw about 150 amps across four 40-amp circuits. The correct tankless water heater wire size depends on the exact model, not just whether the heater is labeled tankless.
For homeowners in San Antonio, Leon Springs, Boerne, Helotes, and the Texas Hill Country, that distinction can change the entire replacement plan. A plumbing upgrade may also require new electrical circuits, a panel evaluation, or a service-capacity review. Getting those answers before purchasing equipment helps prevent an unexpected electrical project after the heater arrives.
Table of Contents
- Wire Size and Breaker Chart by Heater Model
- How to Read Your Heater's Nameplate Before Buying Wire
- Wire Gauge Factors and Code Rules
- Checking Your Panel Before a Whole-Home Install
- Replacing an Existing Tank Heater Circuit
- San Antonio Heat, Older Homes and Panel Limits
- Symptoms That Signal Wiring Problems and Their Fixes
- Confirm the Wiring Before You Buy the Heater
Wire Size and Breaker Chart by Heater Model
The chart below compares published requirements for electric models rated at 240 volts, drawn from manufacturer installation guides and electrical-requirement pages. Read it as a comparison of real specifications, not as a shopping list.
| Heater size | Max current | Breaker(s) | Wire per circuit |
|---|---|---|---|
| 3.5 kW | About 15 A | One 20 A | 12 AWG |
| 6 kW | About 25 A | One 30 A | 10 AWG |
| 8 kW | 33 A | One 40 A | 8 AWG |
| 11 kW, one maker | 46 A | One 60 A | 6 AWG |
| 11 kW, another maker | 57 A | One 60 A | 6 AWG minimum |
| 12.2 kW | 51 A | One 60 A | 6 AWG copper recommended |
| 13 kW | About 54 A | Verify exact manual | One wire set; verify gauge |
| 18 kW | 75 A in the two-circuit example | Two 40 A double-pole in that configuration | 8 AWG in two sets, or 10 AWG in three sets for a different model |
| 24 kW | 100 A | Three 40 A double-pole | 8 AWG, three sets |
| 27 kW | 112.5 A | Three 40 A double-pole | 8 AWG, three sets |
| 32 kW | 133 A | Verify exact model's circuit arrangement | Verify exact manual |
| 36 kW | 150 A | Four 40 A double-pole | 8 AWG, four sets |
Each row is an equipment-specific minimum or recommendation to verify against the exact nameplate, not permission to purchase wire from a generic chart. The alternate multi-circuit configuration is discussed under the panel checks below.
What the rows mean for the panel
The two 11 kW rows carry the same kilowatt label but list different maximum current, 46 A versus 57 A. Both call for one 60 A breaker, yet one specifies 6 AWG while the other states 6 AWG minimum, so the conductor requirement still changes even when the breaker matches.
The 13 kW and 32 kW rows say "verify" because the published specifications do not settle the circuit arrangement. Where the chart says "verify," the missing detail must come from the exact manual, not from the neighboring row.
The 18 kW row shows how manufacturers divide similar heating capacity differently. One configuration runs on two 40 A double-pole breakers with two sets of 8 AWG wire, while a different model of similar output uses three circuits with smaller 10 AWG conductors. Same heating job, different wiring plan.
The 36 kW row lists 150 A as the heater's total demand, spread across four dedicated 40 A double-pole circuits with four separate 8 AWG wire runs. That is the row where a water-heater replacement can turn into a panel or service project, because the panel must supply four breaker spaces and four cable routes rather than one.
Practical rule: A wire-size chart helps identify questions for the installer. It isn't an electrical installation plan.
How to Read Your Heater's Nameplate Before Buying Wire
Two tankless heaters can carry the same kilowatt rating yet still demand different wire, because each manufacturer decides how to divide the heating load across circuits. A 36 kW unit may even call for four dedicated circuits rather than a single heavy cable. The kilowatt figure works like the total dose printed on a prescription: it says how much, while the installation table says how that amount gets split. The label that settles these questions sits on the heater itself.
A clear photograph of that label, plus the matching page in the installation manual, gives a contractor enough information for a useful pre-purchase conversation. An on-site review can still change the estimate, and the manufacturer's manual together with local electrical code always controls the final answer.

Gather the equipment details
Find the exact model number, voltage, and kilowatt rating. The label may sit on the side of the unit or inside an access panel, so use an accessible exterior label or the product paperwork rather than opening an energized compartment.
Record the maximum amperage. The electrician needs the model's stated demand, not a figure estimated from its marketing description. This number may appear on the label or on the specification sheet.
Locate the matching installation table. The manual must cover the exact model, not merely the same product family, because related heaters can require different circuit arrangements.
Count the required wire sets and breakers. A total-current figure doesn't show how the manufacturer divides the load, so the installation table must identify every required circuit.
Add the installation details
Record conductor material and minimum gauge. Copper requirements, insulation ratings, and connection limits belong in the notes, because gauge alone doesn't describe a suitable conductor.
Estimate the route from the panel. Measure along the likely cable or conduit path instead of a straight line through walls, since the installed route determines conductor length.
Look for a distance assumption. Some tables apply only within a stated run length, so the contractor needs to know whether the proposed route exceeds that limit.
Send the information to the installation team. The nameplate photo, the manual page, the route estimate, and a photo of the accessible panel label let the plumber and electrician discuss the same equipment before anything is ordered.
Wire Gauge Factors and Code Rules
Two heaters with identical wattage can ship with different wiring instructions. Gauge charts based on wattage alone miss that, because the conditions the conductor will face once the walls close up are what determine the wiring requirements.
Ampacity means the current a conductor can safely carry under its installation conditions. A wire behaves a bit like a road at rush hour: add heat and crowding along the route, and the same capacity moves less safely. Cable type, conduit, temperature, and the terminals at each end all change what a given gauge is allowed to carry.

Distance and heat affect conductor selection
- Voltage drop: Voltage falls along the conductor while the heater draws current. Electricians commonly design these circuits to keep the drop under 3% under load, so a long panel-to-heater route is a design factor rather than a routing detail.
- Run length: Resistance grows with every foot of conductor, which drops more voltage and generates more heat on longer runs. When a manual's chart assumes a limit such as a 50-foot maximum, a route beyond it needs a recalculation rather than an automatic step to the next gauge.
- Installation temperature: A hot attic or garage reduces allowable ampacity. The electrician must evaluate the actual route instead of treating indoor conditions as uniform.
- Conductor and connection details: Bundled conductors, conduit occupancy, aluminum wiring, and terminal temperature ratings can change the selection. Copper THHN conductors installed in conduit cannot be treated as interchangeable with every cable assembly.
For international background, DLG Electrical's explanation of Australian cable sizing requirements offers a separate regional perspective. The electrical rules adopted in Texas remain the governing standard here.
Protection, permits, and the final design
The breaker exists to protect the conductor. Its rating comes from the heater's installation instructions and the wire installed, and the heater's connections and panel must also support the approved arrangement.
The electrician applies the locally adopted electrical code, including applicable load treatment, grounding, conduit-fill limits, and disconnect requirements, the rules governing how power can be safely isolated for service. Disconnect placement is verified on site rather than assumed from a generic diagram.
For San Antonio-area projects, the licensed professional should confirm the governing jurisdiction, required electrical permits and inspections, and whether separate plumbing approval applies. A load calculation, an evaluation of the home's electrical demand, plus an on-site inspection provides a sounder answer than any gauge lookup.
Checking Your Panel Before a Whole-Home Install
A whole-home electric tankless unit often turns a plumbing replacement into an electrical-service project. The multi-breaker rows in the chart call for open panel positions, separate correctly sized conductors, grounding, and enough spare capacity in the service.
The kilowatt label hides how different the wiring plans can be. One manufacturer splits its mid-range models across three separate circuits, stepping up conductor size as the kilowatt rating climbs. A 36 kW unit can require four dedicated circuits, which is the point most single-gauge charts miss. At that level, buying the heater is the easy part. Feeding it is the project.

Panel approval needs more than empty spaces
- Breaker positions: If the unit calls for three or four double-pole breakers and the panel has no open paired slots, the electrician will schedule a panel upgrade estimate before any installation date.
- Service capacity: If the load calculation shows the service already runs near its limit, the project scope grows to a service upgrade, or the heater choice gets reconsidered.
- Panel condition: If the panel shows corrosion, obsolete breaker types, or aging bus connections, corrective work enters the estimate even when slots remain open.
- Existing tank circuit: If the old circuit's conductors fall short of the new manual's requirements, new wiring goes into the quote rather than assuming a free reuse.
The 36 kW row in the earlier chart shows how demanding the top end gets, and each finding above carries a cost consequence. Catching them during planning keeps the estimate honest.
Older San Antonio homes may need panel modifications, but age alone does not decide the outcome. The electrician should finish the capacity review before the plumber commits to setting the selected unit.
Homeowners coordinating the plumbing and electrical portions can consult electric tankless insights from Stultz Plumbing while preparing questions about installation responsibilities and scheduling.
Replacing an Existing Tank Heater Circuit
A 30-amp circuit that served a storage heater for years still cannot feed a tankless model whose manual calls for 60 amps, no matter how good its condition looks. Reuse is only possible when the old circuit satisfies every requirement in the new unit's manual.
Compare the old installation with the proposed model
Record what is visible. The homeowner can note the breaker rating printed on the handle and the circuit label in the panel directory. A licensed electrician then confirms conductor size, material, and condition, without the homeowner removing the panel cover.
Pull the exact manual row. Breaker count, breaker size, and conductor gauge come from the installation manual for the specific model, not the wattage label on the carton.
Match the requirements against what exists. Reuse is a professional determination measured against the manual, and any shortfall means new wiring enters the scope.
Verify even a similar-rated replacement. Matching kilowatt labels do not prove matching terminals, conductor requirements, or circuit arrangements.
Trace every circuit path. A whole-home unit may require several dedicated circuits, so each conductor run needs its own workable route to the heater location.
Keep the estimate tied to the approved scope
The homeowner should request separate line items for reusable components and for required new work. In the 30-amp example above, the wire, breaker, and route would all appear as new work rather than carry-overs, because the existing circuit cannot serve a 60-amp requirement as wired. When the existing circuit falls short, the honest options are an approved electrical modification or equipment the home can safely support.
San Antonio Heat, Older Homes and Panel Limits
A garage install during a 100-degree July is a different wiring job than the same unit in a climate-controlled closet. Across San Antonio and the nearby communities of Leon Springs, Boerne, and Helotes, the path to the panel often crosses the hottest square footage in the home. The site visit is where the chosen conductor meets those real conditions.
Older housing stock raises the stakes. A 1960s ranch may still run on an original panel with no labeled directory, so the electrician has to map the circuits before anyone can count open positions. That homework matters more when the planned heater calls for several dedicated circuits at once, because a high-kilowatt whole-home unit can turn a water heater swap into a panel project.
Two details help the contractor prepare. First, the likely wiring route: an attic, a garage, finished walls, or a crawl space each involves different labor and materials. Second, the governing jurisdiction, since a San Antonio mailing address can sit inside city limits, a suburb, or unincorporated county land, each with its own permit process.
Panel appearance is easy to misread. An open breaker slot works like an empty parking space: it proves a spot exists, while the load calculation determines whether the service can carry another large load. A panel that looks full means the calculation comes first. Homeowners who learn that distinction at the site visit can approve a scope matched to the actual house, rather than discovering a panel upgrade after the heater arrives.
Symptoms That Signal Wiring Problems and Their Fixes
A breaker that trips when the heater starts deserves professional attention. Possible explanations include a circuit arrangement that doesn't match the model, an unsuitable breaker, or another electrical fault; the symptom alone doesn't identify the cause.
The table below provides inspection priorities, not a remote diagnosis. Wiring symptoms and hot-water complaints can overlap, so a licensed electrician should assess electrical concerns while a qualified plumber evaluates heater performance.
| Symptom | Likely cause | What to do |
|---|---|---|
| Breaker trips when the heater starts | Possible breaker mismatch or heater sharing an unsuitable circuit | Have an electrician match the breaker and circuit to the nameplate |
| Breaker trips after weeks of use | Possible undersized conductor, loose termination, or another fault | Stop using the heater, isolate power if safe, and arrange inspection |
| Warm outlet, discolored wire, or burning smell | Possible loose connection or overheated conductor | Shut off power at the breaker if safe and call a licensed electrician immediately |
| Lukewarm water or hot water runs out early | A heating element or circuit may not be operating; plumbing causes are also possible | Have the installer check all required circuits and heater operation |
| Wire chosen from a generic “8 gauge” guess | Conductor may not match the exact model | Compare the installation with the manual and correct any unsuitable wiring |
Timing helps the electrician, but doesn't prove the cause
A homeowner should describe whether the trip happens immediately, only during hot-water use, or after the heater has operated normally for a while. That history helps the electrician decide what to inspect, but it doesn't justify selecting a replacement breaker without testing.
Discoloration or a burning smell changes the urgency. The homeowner should avoid touching suspect equipment and should not approach a panel that is smoking, sparking, or otherwise unsafe; immediate danger requires emergency assistance.
Inconsistent hot water needs a complete check
On multi-circuit equipment, a missing supply circuit is one possible explanation for reduced heating. An accessible breaker position can be noted without opening the panel, but a double-pole breaker is a linked device, not an invitation to operate its poles independently.
A tripped breaker that resets once still warrants a professional check. Repeated resetting is not troubleshooting, and a larger breaker is never an acceptable guess.
Safety boundary: Homeowners can document symptoms. Licensed professionals should inspect terminations, verify conductor suitability, and make electrical repairs.
Confirm the Wiring Before You Buy the Heater
The safest purchasing order is site approval first, equipment purchase second. Buying the heater first works like ordering furniture before measuring the doorway. The same kilowatt rating can call for different wire sizes from one manufacturer to the next, and a 36 kW unit can require four dedicated circuits, so what looks like a simple water heater swap can turn into a panel project.
The nameplate and panel checklist earlier in this guide covers what to gather first. Those numbers, a look at the available breaker spaces, and the approximate wire route give a contractor enough information for a real assessment instead of a guess based on wattage alone.

What a useful installation proposal includes
- Electrical approval: A load calculation and review of the proposed circuit arrangement.
- Written recommendations: The exact equipment, conductor requirements, breakers, and any panel or service work.
- Permit responsibilities: Clear identification of who handles approvals and inspections.
- An understandable estimate: Plumbing and electrical scopes, exclusions, and homeowner approval before work starts.
For broader international context, AdVoltage Electrical's instantaneous hot water guide offers a useful second perspective. The final word on a Texas installation still comes from the equipment manual and the licensed professionals responsible for the work.
Homeowners planning a tankless water heater upgrade should schedule the plumbing and electrical review together so equipment selection reflects both household demand and what the panel can supply.
For homeowners in San Antonio, Leon Springs, Boerne, Helotes, and the Texas Hill Country, Stultz Plumbing offers water-heater installation evaluations before any equipment is ordered. The family-owned company is led by Master Plumber Jacob Stultz, License #45005, with more than 15 years of experience and 130+ five-star Google reviews, and handles water-heater installation and repair, drain cleaning, water-softener installation, and general plumbing. Visit Stultz Plumbing or call the 24-hour emergency line for a no-pressure diagnosis, an upfront estimate, and 0% financing options on larger projects.
Jean runs growth strategy at AimSetWin, a performance marketing agency specializing in local service businesses across Texas. he's helped plumbers, HVAC companies, pest control operators, and home service brands build predictable revenue systems using data-driven advertising and conversion optimization.


